Phantom Power (48V) Explained: Which Mics Need It?
Share
You plug in your new mic, hit record and... nothing. There's a good chance it comes down to one little button: 48V. That's phantom power. Here's what it is, which mics need it, when to leave it off and how to switch it on safely.
The short answer
- Condenser mic with an XLR cable? Turn on 48V, or you won't hear anything.
- Dynamic mic (like a Shure SM58)? You don't need it. Leaving it on is usually fine with modern mics, it just doesn't do anything.
- USB mic? Phantom power doesn't apply. It gets power over the USB cable.
- Ribbon mic? Check the manual first.
What is phantom power?
Phantom power is DC power that your audio interface or mixer sends to your mic through the mic cable. According to Shure, it's there for condenser mics: they have electronics inside that need power to work. That way you don't need a battery or a separate power supply.
It's called "phantom" because the power travels invisibly over the same cable as your audio signal. There's no extra power cord, but it's there.
Shure lists 11 to 52 volts DC as the worldwide standard, with typical studio mics running on 48 volts. That's why almost every interface simply labels the button 48V.
Why does it only work over XLR?
Phantom power needs a balanced connection. According to Shure, pins 2 and 3 of the XLR cable carry the same DC voltage relative to pin 1. A regular guitar cable won't do it. The Focusrite Scarlett Solo guide, for example, says outright that 48V goes to the XLR mic input only, not to the 1/4" jack input.
Which mics need 48V?
Condenser mics: yes
Almost every condenser mic with an XLR connection needs phantom power. Think of the Audio-Technica AT2020 or the RØDE NT1 over XLR. Without 48V, there's no signal. Shure does mention one exception: condensers that run on a battery.
Dynamic mics: no
A dynamic mic like the SM58 doesn't need phantom power, according to Shure, because there are no active electronics inside. The signal comes from a small coil moving in a magnetic field.
There are exceptions. Focusrite notes that a few dynamic mics have built-in amplification, and those do need power. An inline booster like the Cloudlifter also runs on your interface's 48V. Not sure about your mic? Read Shure SM7B too quiet? Gain, Cloudlifter and FetHead explained.
Ribbon mics: check the manual
According to Focusrite, passive ribbon mics don't need phantom power and active ribbons do. Shure recommends always checking the manual or asking the manufacturer before you turn on 48V with a ribbon mic.
USB mics: not relevant
A USB mic gets its power from the USB connection. Elgato puts it simply: phantom power only applies to XLR connections. Does your mic have both USB and XLR? Then you may need 48V when you use the XLR output. Check the manual.
Can 48V damage your mic?
With modern mics, usually not. Shure says phantom power will not damage other microphones "in the vast majority of cases." Focusrite says the same about dynamic mics: it shouldn't damage the mic, but it's rarely needed.
What you do need to watch out for:
- Old, unbalanced mics. Focusrite warns these can be damaged by 48V.
- Ribbon mics. Always check the manual first.
- Plugging in with 48V on. Shure recommends turning phantom power off while you plug mics in or out. That prevents loud pops that can damage your speakers or headphones over time.
- Other gear on your mic input. Focusrite notes that some line, instrument or headphone outputs can be damaged if you wire them straight into a mic input with 48V on.
How to turn on phantom power safely
- Turn your speakers and headphones down and set your interface gain low.
- Make sure 48V is off.
- Connect your mic with an XLR cable to the XLR input on your interface.
- Press the 48V button. On most interfaces a light comes on. Heads up: on some interfaces one 48V button covers several inputs at once. Check your manual if you also have a ribbon mic or other gear plugged in.
- Wait a few seconds. Then rap or sing your loudest part and slowly turn up the gain until you're nicely in the green, with no red.
- Done recording? Volume down first, then 48V off, then unplug the cable.
No sound, even with 48V on?
Go through this list:
- Are you in the right input? With a combo input the XLR plug needs to be all the way in, and 48V often doesn't go to the jack input.
- Is your cable really an XLR cable, and is it working? Try another one.
- Is your gain turned up enough? Read mic too quiet when recording if you hear something, but very quietly.
- Does your interface actually have phantom power? Shure points out that older mixers and cheaper interfaces sometimes don't. In that case you need a separate phantom power supply between the mic and the input.
- Is your DAW using the right input? That's what mic not working when recording is for, with steps for FL Studio and Logic Pro.
Want a quick check that your mic gives any signal at all? Open the free mic test. You'll see right in your browser how loud you're coming in, whether you clip and how much noise there is. Your audio isn't uploaded.
Next: from a good recording to a good vocal
Once your signal is right, the real work starts: EQ, compression, de-essing, autotune and effects in the right order. Grab the free vocal chain cheat sheet for Logic Pro and FL Studio. Want a starting point with the settings already dialed in? Check out the vocal presets for FL Studio and Logic Pro.
Still deciding which type of mic to buy? Read condenser vs dynamic mic for rap and vocals.
FAQ
What does 48V mean on my audio interface?
That's the phantom power button. It sends power over the XLR cable to your mic, so a condenser mic can work.
Should 48V always be on?
No. Only turn it on when your mic needs it, like a condenser. With a dynamic mic it does nothing for you.
Is phantom power the same as gain?
No. Gain sets how loud your signal comes in. Phantom power is just power for the mic. A dynamic mic that's too quiet won't get louder with 48V.
Does a USB mic need phantom power?
No. A USB mic is powered over USB. Phantom power only applies to XLR.
My interface doesn't have 48V. Now what?
You can put a separate phantom power supply between your mic and the input, or use a dynamic or USB mic instead.
Sources: Shure on phantom power and on common audio myths, Focusrite on phantom power and the Scarlett Solo hardware guide, Elgato on phantom power and LEWITT on the Cloudlifter.